Free Flowmate downpipe protection with your new spouting. Find out more →
CallBook a Free Site Visit
Continuous spouting being roll-formed on site beside a home
News

The Continuous difference: how continuous spouting is made

Continuous spouting is spouting made on site, at your place, in one length along each straight wall of your roof. There are no joins along the run, only at the corners. Fewer joins means fewer places to leak.

Since 1991
Making continuous spouting on site
0
Joins along each straight run
Up to 16
Weeks of training for every installer
15
Locations across New Zealand

How we make continuous spouting

You choose your spouting profile. We bring the matching roll-forming machine to your site. We roll-form the spouting to the exact length of each wall, often right on your driveway. Then we mitre and finish every corner by hand, using traditional sheetmetal techniques.

We started in Auckland in 1991, with one machine towed behind a 1965 Hillman Super Minx. In 1994 we designed and built New Zealand's first fully portable quarter-round machines, for Quartz. In 1998 and 1999 we built the world's first portable 125mm and 150mm half-round machines.

We make Quartz, Chief and Big Chief this way everywhere we work. In some regions we also make Cube 125 and Halo 150 continuously. Quartz is the most popular. In 2024 we installed 221,946 metres of it on Kiwi homes, baches and sheds.

  1. 1991We start in Auckland, with one machine towed behind a 1965 Hillman Super Minx.
  2. 1994New Zealand's first fully portable quarter-round machines, for Quartz.
  3. 1998 and 1999The world's first portable 125mm and 150mm half-round machines.
  4. 2024221,946 metres of Quartz installed on Kiwi homes, baches and sheds.

Continuous vs sectional spouting

Sectional spouting is the kind you buy off the shelf. It comes in set lengths, usually plastic, and gets joined together along each wall. Continuous spouting is made to fit your walls exactly, on site, from steel, aluminium or copper.

Fewer joins, fewer leaks

Every join is a place a leak can start. Ours has joins only at the corners.

Fewer joins also means less silicone and fewer rivets. That saves on cost and installation time. The silicone we do use is Selleys premium silicone, with a UV guarantee.

Steel, aluminium or copper

Choose the material that suits your home and your exposure zone:

  • Prepainted steel

    our CG Range is MagnaFlow Mag-200 steel, with nine corrosion layers. ColorSteel Maxam-150 is also available.

  • Prepainted aluminium

    ColorCote AlumiGard or ColorSteel Altimate. It suits every zone, right down to the coast.

  • Pure copper

    it weathers to a natural patina and carries a 20-year material and perforation warranty.

Your fascia, the board your spouting fixes to, can be matched too. Our Truss Series steel fascia panels come in the same colours as your spouting.

Is continuous spouting right for my home?

It suits almost any home. We install it on new builds, renovations and reclads, and as a replacement for old or leaking spouting. Body corporates and commercial buildings use it too. If your home has an internal gutter, our Conform system swaps it for continuous spouting outside.

Made to measure, with less waste

We form every length to fit the wall it goes on. So there's very little offcut, and very little ends up in a skip. That's why specifiers, builders and homeowners who care about waste choose continuous spouting.

A cleaner roofline

With no joins along the run, you get clean lines and neat mitred corners. You don't get the patchwork look of sectional spouting. We make every part of your system from the same materials, so the spouting, fascia and downpipes stay matched as they age.

Built for New Zealand conditions

New Zealand homes face sun, wind, heavy rain, snow and some of the highest UV levels in the world. Steel spouting doesn't crack in UV or sag under load. In 2015 we switched our whole bracket range from galvanised steel to aluminium. We now offer New Zealand's only full range of aluminium spouting and downpipe brackets, so they won't rust.

We manufacture and test all our spouting and downpipes to AS/NZS 2179.1:2014. Every profile also has our Continuous Emergency Overflow System. It's a gap between the fascia and the spouting. In a heavy downpour, water spills out through it instead of into your home.

A storm rolling in over a New Zealand coastline

Installed by our own teams

We train and employ our own installers. We don't hand the work to contractors. Installers spend up to 16 weeks training with our top teams, and a high percentage have been with us for 10 years or more. They set the fall with string lines, so water runs quickly to your downpipes. Most homes take a day. All we need from you is a power socket.

The Continuous Group Waikato team outside their branch

Where you can get it

Our 15 locations cover the whole of New Zealand. Every one offers a free, no-obligation onsite quote. Your local team measures up, helps you choose a profile and colour, and gives you a clear price before you decide.

Find your local team

Frequently asked questions

Something else on your mind? Your local team is happy to help.

0800 501 993
Spouting we roll-form on site in one length along each wall, with joins only at the corners.
It has far fewer joins, so there are fewer places for leaks to start. It also uses less silicone and fewer rivets, and creates less waste.
Prepainted steel (MagnaFlow or ColorSteel), prepainted aluminium, or pure copper. We match the material to your exposure zone.
Steel doesn't crack in UV or sag under load the way plastic can. Our prepainted steel carries a 15-year perforation warranty.
It depends on your home, the profile and the material. Every Continuous Group location offers a free, no-obligation onsite quote.

Want continuous spouting on your place?

Book a free site visit with your local Continuous team. Honest advice and a clear, up-front quote.